PumpLookupPump and motor part numbers
Mains Units

3 Frame plunger pump

271

  • 13.2Flow, l/min
  • 103Pressure, bar
  • 1420Speed, rpm
  • 2.68Power, kW

50 Hz Rated at a motor speed for 50 Hz mains (UK, Europe, Africa, Australia, most of Asia).

Cat Pumps 3 Frame pump

Specification

Flow
13.2 l/min
Pressure
103 bar
Speed
1420 rpm
Absorbed power
2.68 kW
Plunger
18 mm
Shaft
Solid, Ø16.5 mm
Weight
6.1 kg

Data sheet (PDF, Cat Pumps)

Kits

Seal kits6

Part numberDescriptionPer pumpSuppliers
30735Seal kit, STHT (.3400)1 
30983Seal kit, NBR (STD)1 
33609Seal kit, FPM (.0110)1 
33914Seal kit, EPDM (.0220)1 
33915Seal kit, HT (.3000)1 
76660Seal kit, FFKM (.0770)1 

Valves4

Part numberDescriptionPer pumpSuppliers
30982Valve kit, NBR (STD)1 
31216Valve kit, FPM (.0110)1 
31217Valve kit, EPDM (.0220)1 
76690Valve kit, FFKM (.0770)1 

Exploded view

Cat Pumps exploded view of the 3 Frame pump, with position numbers
Cat Pumps' drawing. The numbers match the positions in the parts list below. Open the picture to zoom in.

Parts list

Positions are the balloon numbers on Cat Pumps' exploded view.

PosPart numberDescriptionQty
5 92538 Screw, HHC Sems (M6 x 16)8
8 27950 Cover, Bearing2
10 26536 O-Ring, Cover, Bearing2
11 24159 Seal, Oil2
15 14487 Bearing, Ball2
20 48867 Rod, Connecting Assembly3
25 46946 Crankshaft, Dual-End (M7.3) (Models: 231, 237)1
25 46951 Crankshaft, Dual-End (M11) (Models: 241, 247)1
25 108062 Crankshaft, Dual-End (M12.7) (Models: 271, 277)1
32 43211 Cap, Oil Filler1
33 14177 O-Ring, Oil Filler Cap1
37 92241 Gauge, Oil Bubble with Gasket1
38 44428 Gasket, Flat, Oil Gauge1
40 92542 Screw, HHC Sems (M6 x 20)6
48 25625 Plug, Drain ( 1/4" x 19 BSP)1
49 23170 O-Ring, Drain Plug1
50 48772 Cover, Rear1
51 48773 O-Ring, Rear Cover1
53 128354 Crankcase1
64 16948 Pin, Crosshead3
65 45114 Rod, Plunger3
69 126259 Washer, Oil (M24)3
70 25301 Seal, Oil3
71 126189 Washer, Oil Seal3
75 43900 Slinger, Barrier3
88 45697 Washer, Keyhole (M18 x 10)3
90 43901 Plunger (M18 x 43)3
95 126550 Stud, Plunger Retainer (M6 x 43)3
96 43235 Backup Ring, Plunger Retainer3
97 17399 O-Ring, Plunger Retainer3
98 44041 Gasket, Plunger Retainer (M12.5)3
99 44031 Retainer, Plunger (M6)3
100 28597 Retainer, Seal3
106 44053 Seal, Low-Pressure with SS-Spring3
110 46425 Manifold, Inlet1
116 15847 Lockwasher (M10)2
117 87950 Screw, HSH (M10 x 35)2
125 44652 Seal, High-Pressure with SS-Support3
139 45156 Plug, Inlet [ 1/2" NPT(M)]1
143 17547 O-Ring, Inlet Valve Adapter, Rear3
150 44060 Adapter, Inlet Valve3
154 43893 O-Ring, Inlet Valve Adapter, Front3
155 26089 O-Ring, Discharge Valve Adapter, Rear3
157 44059 Adapter, Discharge Valve3
159 26089 O-Ring, Discharge Valve Adapter, Front3
164 44058 Seat6
165 44001 O-Ring, Seat6
166 543669 Valve6
167 44056 Spring6
168 44055 Retainer, Spring6
185 46427 Manifold, Discharge1
186 15847 Lockwasher (M10)4
188 87952 Screw, HSH (M10 x 55)4

Motor

A 4-pole motor of at least 2.68 kW drives this pump at 1420 rpm. Single-phase motors are listed last, for a 230 V supply.

MotorkWrpmFrameClassA at 400 VSuppliers
RNE 100b4 31440IEC 100IE36.8  
RN 100b4 31420IEC 100IE16.4  
RNM 100c4 31410IEC 100Single-phase17 at 230 V  
RNM 112c4 31415IEC 112Single-phase18.5 at 230 V  

The contactor and overload relay for each motor are on the motor's page.

Flange

The flange bolts the pump to the face of the motor. It depends on the motor's IEC frame.

  • IEC 100, 28 mm shaft (RNE 100b4, RN 100b4, RNM 100c4) No Cat Pumps flange listed for this motor.
  • IEC 112, 28 mm shaft (RNM 112c4) No Cat Pumps flange listed for this motor.

Coupling

The flexible coupling joins the motor shaft to the pump shaft inside the flange.

  • IEC 100, 28 mm motor shaft No Cat Pumps coupling listed: you need one for a 28 mm motor shaft to 16.5 mm pump shaft.
  • IEC 112, 28 mm motor shaft No Cat Pumps coupling listed: you need one for a 28 mm motor shaft to 16.5 mm pump shaft.

Other Cat Pumps 3 Frame pumps

230231237240241247270277