PumpLookupPump and motor part numbers
Mains Units

7CP plunger pump

7CP6110CS

  • 39.7Flow, l/min
  • 138Pressure, bar
  • 1750Speed, rpm
  • 10.7Power, kW

60 Hz Rated at a motor speed for 60 Hz mains (North America, parts of South America and Asia).

Cat Pumps 7CP pump

Specification

Flow
39.7 l/min
Pressure
138 bar
Speed
1750 rpm
Absorbed power
10.7 kW
Plunger
22 mm
Shaft
Solid, Ø24 mm
Weight
14 kg

Data sheet (PDF, Cat Pumps)

Kits

Valves3

Part numberDescriptionPer pumpSuppliers
31253Valve kit, EPDM (.0220)2 
31256Valve kit, FPM (.0110)2 
34920Valve kit, NBR (STD)2 

Seal kits4

Part numberDescriptionPer pumpSuppliers
31936Seal kit, EPDM (.0220)1 
76068Seal kit, STHT (.3400)1 
76933Seal kit, NBR (STD)1 
76950Seal kit, FPM (.0110)1 

Exploded view

Cat Pumps exploded view of the 7CP pump, with position numbers
Cat Pumps' drawing. The numbers match the positions in the parts list below. Open the picture to zoom in.

Parts list

Positions are the balloon numbers on Cat Pumps' exploded view.

PosPart numberDescriptionQty
5 126540 Screw, HHC Sems (M8 x 20)8
8 131405 Cover, Bearing
9 49503 Shim, Split, 2-Piece, Outer0
10 12393 O-Ring, Bearing Cover-70D2
11 49190 Seal, Oil Crankshaft
12 49504 Shim, Split, 2-Piece, Inner0
15 63479 Bearing, Roller2
20 48727 Rod, Connecting Assembly3
25 49498 Crankshaft, Single-End (M21.7) (7CP6110CS, 7CP6110CSG1)1
25 49649 Crankshaft, Single-End (M26) (7CP6170G1, 7CP6170G118)1
25 46963 Crankshaft, Dual-End (M26) (7CP6170)1
30 131407 Cover, Blind Bearing (7CP6110CS, 7CP6110CSG1, 7CP6170G1, 7CP6170G118)1
32 43211 Cap, Oil Filler1
33 14177 O-Ring, Oil Filler Cap-70D1
36 129343 Gasket, Flat1
37 92241 Gauge, Oil, Bubble with Gasket-80D1
38 44428 Gasket, Flat, Oil Gauge-80D1
39 49948 Dip Stick (White)1
40 125824 Screw, HHC Sems (M6 x 16)4
48 25625 Plug, Drain ( 1/4" x 19 BSP)1
49 23170 O-Ring, Drain Plug-70D1
50 131403 Cover, Rear1
51 14030 O-Ring, Rear Cover-70D1
53 131400 Crankcase1
64 46969 Pin, Crosshead3
65 46968 Rod, Plunger3
70 48281 Seal, Oil Crankcase3
75 43328 Slinger, Barrier3
90 48559 Plunger, Ceramic (M22 x 55)3
95 126555 Stud, Plunger Retainer (M6 x 50)3
96 43235 Backup Ring, Plunger Retainer3
97 17399 O-Ring, Plunger Retainer-80D3
98 45891 Gasket3
99 46504 Retainer, Plunger (M6)3
100 46964 Retainer, Seal3
106 49644 Seal, Low-Pressure with SS-Spring3
120 48279 Case, Seal3
121 13984 O-Ring, Seal Case-70D3
127 48278 V-Packing6
128 48280 Adapter, Male3
162 43248 Backup Ring, Seat6
163 43249 O-Ring, Seat-80D6
164 44718 Seat6
166 43721 Valve6
167 43751 Spring6
168 44564 Retainer, Spring6
172 17617 O-Ring, Valve Plug-90D6
174 43850 Plug, Valve6
185 48274 Head, Manifold1
188 126513 Screw, HSH (M8 x 70)8
500 8081 Gearbox 1" Shaft (See Individual Data Sheet)1
500 8072 Gearbox 11/8" Shaft (See Individual Data Sheet)1

Motor

Rated at 1750 rpm, the speed of a 4-pole motor on a 60 Hz supply. The motors below are listed with their 50 Hz figures and are at least 10.7 kW. Order the one you pick wound for 60 Hz and your supply voltage.

MotorkWrpmFrameClassA at 400 VSuppliers
RNE 160Ma4 111475IEC 160MIE322.4  
RN 160Ma4 111450IEC 160MIE122.4  
RN 132Mc4 uprated 111430IEC 132MIE124  

The contactor and overload relay for each motor are on the motor's page.

Flange

The flange bolts the pump to the face of the motor. It depends on the motor's IEC frame.

  • IEC 132, 38 mm shaft (RN 132Mc4) No Cat Pumps flange listed for this motor.
  • IEC 160, 42 mm shaft (RNE 160Ma4, RN 160Ma4) No Cat Pumps flange listed for this motor.

Coupling

The flexible coupling joins the motor shaft to the pump shaft inside the flange.

  • IEC 132, 38 mm motor shaft No Cat Pumps coupling listed: you need one for a 38 mm motor shaft to 24 mm pump shaft.
  • IEC 160, 42 mm motor shaft No Cat Pumps coupling listed: you need one for a 42 mm motor shaft to 24 mm pump shaft.

Other Cat Pumps 7CP pumps

7CP6110CSG17CP6111CS7CP6111CSG17CP6160CS7CP6160CSG17CP6160CSG1187CP6165CSG17CP6165CSG1187CP61707CP6170G17CP6171CS7CP6185CS